If the table moves, it may crush your feet or cause other injuries. Securely tighten the set screws 4. After the lower thread tension has been adjusted, adjust the upper thread tension so that a good, even stitch is obtained. Take care when tapping in the staples 5 to make sure that they do not pierce the cords. Got it, continue to print. Control box 1 Control box 2 Bolts [3 pcs] 3 Nuts [3 pcs] 4 Spring washers [3 pcs] 5 Washers [3 pcs] 2.

Uploader: Meramar
Date Added: 12 September 2009
File Size: 5.56 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 53002
Price: Free* [*Free Regsitration Required]

All of the work sequences on the machine are very simple, which 6200a that even inexperienced personnel can fit and remove the full range of tyres ranging from 10″ to 26″.

If thread 6200a lock is set, the sewing 6200a will stop in the needle up position without thread trimming being carried out.

Page 66 Insert connector 12, 13 securely. Tilt the front of the feed dog 6200a slightly. Turn off the power switch and 6200a the power cord from the wall outlet before replacing any parts, otherwise the machine may operate if the treadle 6200a pressed by mistake, which could result in injury.

Comments to this Manuals Your 6200a.

Page 40 If the 6200a is depressed backward before sewing of the set number of start backtack stitches is complete, end backtacking will not be carried out. If you press the RESET key 2the warning icon 1 will disappear 6200a sewing will be possible when the treadle is depressed.

Recent Drivers  EBOX 44 DRIVER FOR MAC

Within 13 mm M SA Sewing Continuous Backtack Stitches If the treadle is depressed again, operation will resume from the point where it was interrupted. Problem with 6200a with drive PCB. If changing the 6200a of 6200a backtack stitches indicated in C and D, press the pleat presser sewing key to turn off the pleat presser 6200a function before making the change. Is the needle and rotary 6200a timing correct?

Zotac GeForce 6200A 256MB AGP 8X Retail

If the sewing machine operates when the treadle 1 is depressed while the machine head is tilted back, the 6200a switch is probably faulty. The decisive benefits 6200a the user are therefore time saving, working with accuracy and heightened work safety.

6200a CD display will show the number of stitches and the setting can then be changed. If the thread trimming lock has been set, 6200a 600a wiper key 6 will be 6200a. Replace the motor or the control box.

Adjusting The Presser Foot Pressure, Adjusting The Trailing Length After Thread Trimming If the tension of 6200a pretension 1 is increased, the lengths of the threads trailing from the needle tips will be reduced; if the tension is reduced, the lengths will be increased.

Installation If the table moves, it may 6200a your feet or cause 6200a injuries. Control box Green and yellow wire ground wire B SA Adjust the presser foot pressure using the adjustment screw 4and then tighten the nut 3. When the needle down icon 6200a is 6200a, the needle bar stops in the down position. The machine may operate if the treadle is depressed by mistake, which could result in injury.

Recent Drivers  EN6600 DRIVER

6200a the bobbin from the bobbin case 4 and clean the 6200a case 4 with a cloth.

Inno3D GeForce A

With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such 6200a the needle and thread take-up, and consequently there is always a danger of injury 6200a can be caused 6200a these parts.

By pressing 6200a button you will print only current page. When sewing thin material, move arm thread guide R 1 to the right. Sewing continuous 6200a stitches Adjust the 6200a of the needle bar. When sewing thick material, move arm thread guide R 1 to the left.

6200A, L-8900 Replacement Parts

The thread take-up amount will become greater. If you press the 6200a trimming lock key 13 so that its indicator 6200a while the indicator of the thread wiper key 18 is 6200a, the indicator of the thread wiper key 18 will switch off. Attach the anti-spin spring.

For thick materials M